Note: This wallpaper must be pasted on the wall, and the wall must be flat, and it can only be pasted by touching it. Be sure to seal the surface that can be adsorbed and separated before pasting wallpaper. After the wallpaper is attached to the wall, wipe it back and forth with a dry cloth several times to make the wallpaper and the wall more closely combined.
1. In order to achieve the expected effect, this product must be attached to the smooth surface of the object, and the wall must be dry and free of mold, grease or other dirt. If you want to paste wallpaper on a rough surface, the first step is to smooth it with sandpaper and clean it with water or neutral detergent to avoid affecting the use effect.
2. According to the size of the surface of the object you want to paste, cut out the product with the corresponding size. Leave a blank of about 5 cm.
3. Tear off the film from the backing paper, pull the film forward with one hand, and flatten the film surface from the middle to both sides with the other hand. It's easier to flatten with a soft cloth.
4. When you start pasting, it is recommended that you paste along the wall from top to bottom, and gently accumulate bubbles and folds from the middle to both sides. Large bubbles can be punctured with needles to squeeze out air.
Question 2: How to paste the self-adhesive wallpaper and how to spray sand on the wall? This kind of self-adhesive wallpaper is very simple. You can also refer to the post-it method. Sandblasting depends on what kind of sand you spray. Your questions are so wide that you can't answer them. Remember to adopt the answer.
Question 3: How to paste pvc self-adhesive wallpaper directly? But before pasting, check whether the wall is smooth. It's best to deal with the protruding parts of the skin first. If you want to paste it well, you still need to find a master who can paste it. Find a wallpaper installer on Master Wan's wallpaper installation platform to help you paste it, and there is not much money.
Question 4: What should I pay attention to when pasting pvc self-adhesive wallpaper? How to paste self-adhesive wallpaper:
1. Wipe the dust and grease on the surface of the position to be pasted and dry it (the pasting surface should be smooth and not wet).
2. Before pasting, hold the sticker to indicate the position, and then measure the cutting.
3. From top to bottom, carefully paste the wallpaper and gradually remove the backing paper on the back. While removing the backing paper, gently smooth it from the center of the wallpaper to both sides with a soft cloth or towel to discharge all bubbles to ensure smooth effect.
4. If there are bubbles after pasting, stick them with a needle to let the air escape. Although the wallpaper is self-adhesive, you should find an experienced wallpaper installer to help you. It is suggested that it is best to ask the wallpaper installer of Master Wan's wallpaper installation platform for help, because there may be wrinkles, curling and bubbles if you paste it yourself. It is easy for you to paste it, but it is not easy to tear it off if it is broken.
Question 5: How to paste the self-adhesive wallpaper of 1 Fill the concave hole in the wall with putty, and scrape the wall with a scraper.
2. Measure the wall size, and then measure the wallpaper according to the wall area. Pay attention to the length of wallpaper, which is 5Cm more than the actual veneer.
3. Then, add water to the powder wallpaper glue, mix the ordinary wallpaper with 1: 3, mix the foamed wallpaper with 1: 2, or glue it with special wallpaper that does not need to be mixed, and brush it evenly on the back of the wallpaper with a roller brush.
4. Next, lean the wallpaper against the wall and paste it from top to bottom and from corners to inside with a wooden handle brush to make the wallpaper smooth.
5. When you meet the power switch or socket, cover the wallpaper first, then brush it flat with a wooden handle brush, then draw a cross on it obliquely with a utility knife, press the scraper against the edge of the switch, and cut off the redundant part with a utility knife.
6. If the printed wallpapers are connected together, find the position where the patterns are consistent at the joint of the two wallpapers, overlap and paste them, and the width is about 12cm. After the whole wallpaper is aligned, use a scraper to resist it, and then use a blade to cut off the overlapping parts.
7. Pay attention to pasting wallpaper from top to bottom. If you find that the laitance is uneven, you can wet it with a towel and then scrape it with a scraper.
Ding 8. Finally, treat the wallpaper around the doors and windows like the wallpaper at the power switch.
9. After the wallpaper is pasted, put it back to the original equipment.
(A) Yang Jiao wallpaper posted.
Step 1: Paste the wallpaper carefully with a scraper, over the convex corner, but not on the other wall.
Step 2: Draw a crease at the convex corner from top to bottom by hand, and draw a vertical line from the ceiling to the floor at a distance of 2 .5cm from the convex wall.
Step 3: Cut the wallpaper along the vertical line with a utility knife and guide it with a ruler.
Step 4: Carefully open the remaining wallpaper and put it on the workbench for later use.
Step 5: flatten the extended part of the wallpaper with a seam pressing roller, and then add glue to the covered wallpaper.
Step 6: Mount the covered wallpaper, put the patterns together, scrape the wallpaper clean with a scraper, and flatten it with a press wheel.
(2) Stick wallpaper in the shade.
1, Treatment of non-settlement of internal corners of houses
Step 1: Measure from the center of the last wallpaper to the concave corner, add 2.5cm, and cut out a piece of wallpaper according to this width.
Step 2: Paste the above-mentioned section of wallpaper, align it with a piece of wallpaper, and level it at the concave corner.
Step 3: Scrape the scraper up and down to make the protruding part stick to the wall, and dry the glue on the scraper.
Step 4: Measure the width of this section outward from the concave corner, add 5mm, and mark it on the wall.
Step 5: put a level on the pencil mark to check whether it is really vertical, and apply glue to the covered wallpaper.
Step 6: Align the outside of the covered wallpaper with the vertical line, and paste the remaining wallpaper in the room based on this vertical line.
2. Settlement treatment method of internal corners of houses.
Step 1: Measure from the center of the last wallpaper to the concave corner, add 2.5cm, and cut out a piece of wallpaper according to this width.
Step 2: Paste the above-mentioned section of wallpaper, align it with a piece of wallpaper, and level it at the concave corner.
Step 3: Scrape the scraper up and down to make the protruding part stick to the wall, and dry the glue on the scraper.
Step 4: Overlap and paste another wallpaper with the previous wallpaper, align the floral wallpaper and turn to the other wall.
Step 5: Level the back of the scraper at the inner corner.
Note: first, slowly press the wallpaper to the place near the internal corner by hand, and then slowly smooth the internal corner on the back of the scraper. Don't use force to avoid damaging the wallpaper.
Step 6: Use a ruler and a utility knife to cut from top to bottom along the crease repaired by the scraper at a distance of 2mm from the internal angle.
Step 7: Tear off the excess wallpaper and wipe off the excess glue with a white towel or sponge.
Content reference leju.com
Question 6: How to paste wallpaper in teaching video to beautify home space? In addition to the existing decoration, the use of wallpaper or frills, rich colors and changeable factors can add creativity and imagination to the cold wall.
The materials of wallpaper can be divided into paper and plastic. There are also differences in adhesive parts, among which self-adhesive is the best, because it has been coated with adhesive on the back of wallpaper, and it can be pasted by tearing off the backing paper, but it should be noted that it is difficult to modify once it is pasted. Another kind of dry glue is to apply dry paste on the back of wallpaper, and then paste it with a brush or sponge. There is also a wallpaper that does not use adhesive at all, which is difficult to construct, but there are relatively many materials and patterns to choose from. Here, we will introduce the construction and pasting methods of this wallpaper, hoping to help you instantly change your living space and make it look romantic!
Tools/raw materials
Wallpaper remover, nozzle, wallpaper remover, rubber brush, flat brush, plastic scraper, roller.
Steps/methods
1, eliminate old wallpaper
Step 1: First pour the wallpaper remover into the nozzle and spray it on the old wall.
Step 2: Scrape several holes in the wall with a blade to make the wallpaper remover easy to penetrate.
Step 3: After about 3 minutes, scrape off the old wallpaper with wallpaper knife.
2. The secret of perfect construction: clean up the wall when pasting new wallpaper and tear off the old wallpaper. As for the painted surface, it should be patched and leveled first. Because the wallpaper is relatively long, when applying wallpaper glue, Xuan will fold the wallpaper into an S-shape while applying it to save space. Wallpaper should be pasted from top to bottom, in the same direction from left to right, step by step.
Wallpapers without flowers overlap about 1-2 cm at the overlap of each long wallpaper. As for the wallpaper with flowers, it must be adjusted according to the color. There is a switch cover on the wall when wallpaper is pasted. Solution: the whole wall is still pasted flat, and then it can be cut along the outer frame of the switch cover with a utility knife after it is fully pasted. If the wall is very uneven, it is recommended to stick a layer of backing paper before the sticker, but it is not absolutely necessary.
Treatment of small bubbles: At present, most wallpaper is very convenient to paste and it is not easy to produce bubbles. But if there are really small bubbles, you can squeeze them out with a fine needle and flatten them.
Step 3 paste new wallpaper
1, slowly add water to dilute the wallpaper adhesive.
2, adjust to the appropriate concentration.
3. Spread the adhesive evenly on the wallpaper with a rubber brush and fold it into an S-shape 10 minute.
4. Pay attention to whether the pattern is correct when pasting wallpaper.
5, reoccupy flat brush, pay attention to the need to reserve 3-5 cm at the top of the wall, to facilitate adjustment.
6. Scrape it flat again with a plastic scraper.
7. Flatten the joint with a roller.
8. After the adhesive is dried, cut off the excess part with a blade.
Matters needing attention
Generally speaking, people think DIY is a very hard job. For example, wallpaper pasting has always been considered a complicated matter and must be done by professional workers. Actually, it's not. DIY has no distinction between men, women and children. So, if you are willing to try, everyone can do it. Here, I will provide you with a note for pasting wallpaper yourself, and the rest of the essentials of DIY at home can be referenced.
Before pasting wallpaper, you need to determine what color and pattern wallpaper to choose. The tools you need to prepare are scraper, roller, brush, cutter and so on. Then, follow these steps.
1. Scrape off the old paint on the original wall first. If it is old wallpaper, be sure to tear it off first, and then clean it up with a scraper.
2. If there is a concave hole in the original wall, the hole must be filled with soil, and then leveled with a scraper to keep the wall flat.
3. Measure the size of the wall and paper. If it is a colored wallpaper, you should align the colors neatly every time you paste it.
4. Finally, after cutting the wallpaper, paste it with special glue, paste it evenly with a roller or brush, and then stick it on the wall. These movements are inertial. There are some places to pay attention to, such as when pasting the glued wallpaper, use a brush or roller to brush from the inside to the outside at the edge, and never brush from the outside to the inside, because when the wallpaper is fixed, there will be some gaps, and the air between these gaps will make the wallpaper smooth.
5. In addition to wallpaper, take painting as an example. Similarly, don't brush in different directions. If you brush up and down, the direction is mainly up and down from beginning to end. Brush left and right, the color is exactly the same, leaving no trace. This is a small place to pay attention to when painting. ...& gt& gt
Question 7: Can the self-adhesive wallpaper be torn off? How to tear it off? Don't tear it off ~ tear it to one side, which means that the torn wall will leave a bright line with the surrounding walls. Unless you are ready to redecorate and paint.
Question 8: How to paste and use self-adhesive wallpaper:
Note: This wallpaper must be pasted on the wall, and the wall must be flat, and it can only be pasted by touching it. Be sure to seal the surface that can be adsorbed and separated before pasting wallpaper. After the wallpaper is attached to the wall, wipe it back and forth with a dry cloth several times to make the wallpaper and the wall more closely combined.
1. In order to achieve the expected effect, this product must be attached to the smooth surface of the object, and the wall must be dry and free of mold, grease or other dirt. If you want to paste wallpaper on a rough surface, the first step is to smooth it with sandpaper and clean it with water or neutral detergent to avoid affecting the use effect.
2. According to the size of the surface of the object you want to paste, cut out the product with the corresponding size. Leave a blank of about 5 cm.
3. Tear off the film from the backing paper, pull the film forward with one hand, and flatten the film surface from the middle to both sides with the other hand. It's easier to flatten with a soft cloth.
4. When you start pasting, it is recommended that you paste along the wall from top to bottom, and gently accumulate bubbles and wrinkles from the middle to both sides. Large bubbles can be punctured with needles to squeeze out air.
Question 9: I bought self-adhesive wallpaper online and want to paste it at home. How to post it? Most companies provide you with video tutorials. Ask customer service and just do it.