Faucet installation technology faucet installation method
Installation technology of faucet
1, prepare the installation tools first, and check whether the supporting parts are complete before installation. Common faucet parts include: hose, rubber washer, shower head, drain, strap, decorative cap, etc. And waterproof tape must be prepared.
2. Check whether the main tap water valve is closed.
3. Wind the faucet thread clockwise for several turns with waterproof tape (this is very important, the direction of waterproof tape must be wound clockwise, and the winding is not leaking, that is, the direction of waterproof tape should be opposite to the direction of faucet thread).
4。 Screw the faucet clockwise on the water pipe connector and tighten it with a wrench.
6, open the tap water main valve, normal water supply.
Installation of single-hole basin faucet
Pay attention to the diameter of the outlet when you pay for the faucet of the basin. Most markets are hard water, so you should pay attention to the height of the water inlet and get down from the basin. 35 working points are the most suitable. When installing, you must choose a special angle valve and fix it with the hot and cold water pipes of the wall socket. When you find the distance between the angle valve on the faucet and the water pipe, please buy a special extension pipe for connection. Remember, don't use other water pipes, because the water pressure is too high, it is easy to fall off and leak, which will hurt you. If the water inlet pipe is too long to exceed the water outlet pipe, the part can be cut off as needed. If the angle is not suitable, please bend it to the required position as needed. Remember: don't bend to 90 degrees or more. Please don't forget to buy a small tap (tap short circuit) when filling the basin with water. Don't forget to flush the water pipes buried in the wall before installation.
Install shower and bathtub faucet (wall faucet)
When buying showers, bathtubs and wall-mounted faucets, you can choose a suitable height to bury water pipes. The distance between hot water pipe and cold water pipe must be 15cm. Before installation, don't forget to flush the water pipe to avoid water quality exceeding the standard and damaging the faucet.
Hidden shower and bathtub faucet: After purchasing the hidden faucet, the valve core of the water gate valve should be embedded in the wall. Pay attention to the thickness of the bathroom wall before embedding. If the wall is too thin, the spool will not be buried. The plastic protective sleeve of the valve core is not easy to disassemble when buried, so as to prevent cement and other sundries from damaging the valve core when buried. In addition, when the valve core is embedded, we should also pay attention to the up, down, left and right directions of the valve core to avoid the valve core being buried. When the wall-mounted faucet is embedded in the water pipe in advance, the size has deviation, and the position can be adjusted by adjustment.
Install thermostatic faucet
Please check whether the water pipe is cold or hot before installing the thermostatic faucet. Remember not to install hot and cold water pipes by mistake to prevent the faucet from working normally. Because the water pressure is too low, gas and solar water heaters cannot use thermostats. Please install a constant temperature faucet and don't forget to install a cold and hot water filter.
Single-hole kitchen faucet
The installation of kitchen faucet needs stability, because kitchen faucet is often used and easy to move and move, so the locking nut must be tightened. Some taps are added to the screw to tighten the nut. This is very stable. If the problem of water removal can be solved, it will become a popular trend in the future.
Install a single-handle kitchen faucet
Ordinary single-handle faucets are equipped with installation dimension drawings and instructions for use when they leave the factory. It should be opened before installation and use. General fittings shall be equipped with: 1, a full set of fixing bolts, fixing copper and gaskets; 2. Complete basin dewatering device; 3. Two water inlet pipes. Then move the faucet up, down, left and right to move the handle. It has a slight and uniform blockage, and is light and easy to open and close. Then check the electroplated surface with light, and there are no bubbles, spots and scratches.
Installation method of faucet in installation process of faucet
The types of faucets we use are different, and different faucets will be installed differently. The above is the basic overview and introduction of Bian Xiao. I'll explain it to you today. I believe that everyone knows more or less. I hope this article can help you. You can also log in to Tuba Rabbit to view and subscribe to more relevant content and information.
Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp； Wb, you can get it for free ~