1.: The partition of the shoe cabinet should not reach the end. Leave a little space so that the dust from the shoes can leak to the bottom layer. Install lights above the sink and gas stove. When deciding the location of the bathroom floor drain, you must first think about it and measure the size. The floor drain is best located on one side of the brick. If it is in the middle of the brick, no matter how tilted the brick is, the floor drain will not be at the lowest point.
2. The bathroom and air-conditioning sockets are not designed with switches. Especially for bathroom electric water heaters, it is better to use a two-stage switch with one plug. If you want to turn off the electric heat, pulling out the plug is dangerous
3. Regarding the treatment method of the external corner of the tiles, it all depends on the level of the workers. If the plasterer's skills are good and the tools for grinding ceramic tiles are better, you should not hesitate to choose the 45-degree angle grinding method. From the effect point of view, as long as the grinding is done well, the 45-degree angle grinding method is the most beautiful! If the skill of the workers is indeed not very good, then you should choose to use external angle strips, because the poorly ground 45-degree angle method is not as effective as using external angle strips
4. After draining the water pipes Pressure testing of water pipes is also very important. Everyone must be present during the test, and the test time should be at least 30 minutes, preferably one hour if conditions permit. 10 kg of pressure is applied, and the test can be passed only if there is no reduction in pressure.
5. When building a plastic steel door, be sure to calculate the size of the plastic steel door frame protruding from the wall, and inform the installer so that the final door frame and the wall with ceramic tiles are flat, which is both beautiful and beautiful. Good for hygiene.
6. The carpenter’s door coverings and the masonry’s tiling must also match. When covering the door covers, you must consider whether the ground below (any side of the ground on both sides of the door) needs to be tiled or not. Other cement mortar leveling matters, because if the door frame is nailed before applying the ceramic tiles, it will be wrapped all the way to the ground. When cement is used in the future, if the cement and the door frame are stained, it will cause the wood of the door frame to absorb water and become moldy
7. The bottom of the mattress and the bed board must be breathable. It is generally best to use cedar boards for bed boards
8. Use paper tape as much as possible when painting
9. Pay attention when buying lamps: generally try to use glass, stainless steel, copper or wood (shelf) Yes, generally don’t buy iron with other coatings, paint, etc., as it is easy to fade.
10. Try to use ceramic basins for washbasins, as glass basins are difficult to clean.
11. You must plan the renovation of water and electricity by yourself, and ask them to open the basin in a straight line. I watched them draw the lines and opened the cao according to the drawn lines. Each item must be checked and accepted by yourself.
12. Waterproofing must be done well and the water must be tested!
13. Many verbal agreements in construction have become a gap for being ripped off at checkout. They must be written in black and white. The price of any increase or decrease in items must be asked clearly and written down!
14. If the floor is installed on the ground, the ground must be re-cemented and smoothed.
15. For the kitchen door, it is better to have a wooden hanging rail door made by a carpenter who is renovating.
16. Install as many power plugs as possible in the living room.
17. There should still be a partition outside the shower in the bathroom. Don't try to save trouble by pulling up a shower curtain. It's actually very inconvenient and water will flow all over the floor.
18. The materials for doors and door frames should be chosen with fine wood grain.
19. Before installing cabinets, be sure to confirm whether the waterway in your home is OK.
20. Don’t choose white for kitchen and bathroom floor tiles.
21. Pay special attention to smoothing the putty on the ceiling before applying Dulux
22. The number of lights in the living room should not be too many and should be simple, otherwise it will look like a lighting store! ! !
23. When buying things that need to be installed, try to ask the seller to install them. If installation is not included, you must insist on paying the full price after the installation is complete! !
24. During the renovation, carry the business cards of the manufacturers and merchants that you have collected before.
25. It is best to remove the protective film of the aluminum gusset plate before installation.
26. It is best to use shutter doors for shoe cabinets to prevent odor. You can leave a socket next to the shoe cabinet for drying shoes.
27. A small lamp can be placed where the vegetables are cut.
28. If convenient, the restaurant can also arrange a fan so that the ceiling of the hall will not be stained when eating hot pot or grilling.
29. It is best to arrange a cabinet for storing sundries at the door, which can be placed on top of the shoe cabinet. It is very convenient to put commonly used things such as umbrellas, bags, scissors, change, frequently taken medicines, etc. there.
30. There is absolutely no need to use an expensive ceiling. If you are not too worried about moisture and oil fumes, it is recommended to use moisture-proof gypsum board with waterproof paint. A guest bathroom in my house did this, and it is very beautiful. If you must use aluminum gusset ceilings, it is recommended that 1. not too expensive, 2. use solid colors, especially for kitchen ceilings, pure white is very good. Unless the colors match the decoration style, it will easily be inconsistent. , 3. Make up your own mind, don’t believe those who sell smallpox, their vision is really vulgar. 4. Keep an eye on the scene yourself. It is very important to close the edges. Don't let them be sloppy, otherwise they will leave black seams, which will look ugly no matter how you look.
31. The third day is mainly about drilling holes and continuing to paste the ceramic tiles. The exhaust holes of the range hood and water heater must be drilled in advance. If you wait until the ceramic tiles are pasted before drilling, it will not work. Convenient. Therefore, before decorating, be sure to select range hoods, stoves, water heaters, etc. to determine the size of the holes.
32. Considering that although the custom-made cabinets are beautiful, they are not durable, after considering the opinions and experiences of some students online, the base cabinets are made of cement, with porcelain tiles on the inside and outside, and marble on the countertop. Wall cabinets and cabinet doors are still made of wood. The cabinets made in this way are durable and moisture-proof. And it doesn’t cost much. Many neighbors saw it and said yes, this is not my fault.
33. After the door covers are completed, the plasterers will begin the installation of plaster lines and plastering on the walls. The walls of my house are originally relatively flat, so just 2-3 coats are enough. When criticizing the dust, you need to criticize and polish it once, then apply primer, sand it again after brushing, and finally brush the topcoat twice with ICI. The whole wall looks smooth and even, which is really good. After the wall and ceiling project was completed, the carpenter started making the wardrobe. The wardrobe is made of 18cm Weiye brand large core board, with a decorative panel on the outside. Although it is not as beautiful as the one bought in a furniture store, it is durable and the quality should be better than those bought in a furniture store. I'm not afraid to stand on the cabinet board. I'm afraid it won't work if you buy it. The back plate is also relatively thick, the one I bought is very thin.
34. Other students must pay attention to the following points when laying ceramic tiles: ① It is best to be on site ② Some imperfect tiles can be pasted by workers in places that cannot be seen in the future, such as Behind cabinets, sinks, mirrors, etc., you should also be careful not to place tiles, waist tiles, etc. in the above positions by workers, otherwise you will not be able to see anything in the future and you will spend money in vain. ③Before pasting wall tiles and floor tiles, they must be soaked in water for sufficient time. ④Be sure to plug the floor drain with something to prevent cement from falling down and clogging it. The floor drain in my house was clogged because of falling cement. I spent 30 hours trying to find the management office to clear it, and a lot of small pieces of mud came up. ⑤ When people are on site, workers will not waste too much ceramic tiles. My family was not there when the tiles were being laid, but when I went to see them later, I was heartbroken that a lot of tiles were wasted. It was all hard work.
35. The length and height of a wall. For example, if a bathroom has four walls, the length and height of each wall must be measured. Then deduct the area of ??windows and doors. Finally, calculate the area of ??the ground.
After you measure the dimensions, you can also take them to a store that sells ceramic tiles, and they will help you match them. Just add 5 losses.
36. It is best to have dual-control ceiling lights in the bedroom, one by the door and one by the bed, so as to avoid having to lie in bed and turn off the lights again in the winter.
37. The location, height and spacing of the sockets must be calculated well. First, I encountered a steel bar at the location where I was laying the cassette. Then I placed the cassette and found that it was blocked by the TV cabinet, microwave oven, and desk. I had to move the first two pieces of furniture higher. In the end, I found that not only was the height not in line with ergonomics, but it was also unaffordable. Suitable stainless steel cabinet legs can only be customized with aluminum legs.
38. Just install one at each corner of the aisle, which is bright and effective.
39. When installing the lamp, I did not consider the position of the dining table, and now the lamp is not in the center of the dining table.
40. Don’t use too plain bathroom tiles. First, they will get dirty easily, and second, they will look dull over time!
41. More sockets should be installed, furniture should be purchased from outside, the floor should be stain-resistant and safety should be considered, sample rooms should be seen more, and principles should be adhered to
42. Aluminum gussets are not available at all It is necessary to buy high-priced, very cheap aluminum gussets that are far better than PVC. No matter how much you spend, you will not see a significant difference. When buying aluminum gusset plates, you should pay special attention to the keel rather than the aluminum gusset plate itself (the object of the aluminum gusset plate is too large to be manipulated). Ghosts are often found on the keel.
43. It is difficult to find a satisfactory color for the floor tiles, and I have not found one. However, staggering two unsatisfactory colors and turning them at a 45-degree angle can achieve an effect that I am very satisfied with. This is a good suggestion put forward by the bricklayer himself.
44. If you install a cabinet on the top of the balcony, adding a layer of foam plastic board on the back of the cabinet will have a very good thermal insulation and waterproof effect. It is best to use fireproof boards for balcony cabinet doors to keep them from deforming. The environment on the balcony is relatively bad.
45. If you don’t have suitable wood moldings, you might as well have them custom-made. The quality of the custom-made ones seems to be better than the samples. And customization is more personalized.
46. The stainless steel legs used for bathroom floor cabinets are huge profits. Find some places behind the store to buy them at extremely cheap prices.
47. When installing a door lock, pay attention to the wax on the lock tongue. If it is damaged, it will be too late to apply wax. If there is no door catch, be careful to prevent the handle from hitting the wall and being damaged. 48. Paco flooring is very good and I like it. The only thing I have to remind you is that it may be better to negotiate the price directly with the boss than with the salesperson.
49. Matte paint is more beautiful than high-gloss paint
50. If you renovate, you will use finished putty instead of talcum powder
51. Install leakage protectors and The air switch junction box cannot be saved, and should not be placed outdoors but indoors. Originally, I wanted to save labor and money by using the old junction box outside the door. The electrician suggested replacing it with a new one indoors. Now I found that he A little advice is valuable.
52. The leakage protector and air switch should be from famous brands. I use "Meilan Geran". If you want to buy genuine goods, it's easy. Just call and check the phone number of Merlin Gerin's headquarters, and then call and ask for the local branch number. 53. Under-counter basins are more elegant than above-counter basins, look better, and are easier to clean. When fitting an under-counter basin faucet, please note that the mouth of the faucet should be longer due to the thickness of the basin rim.
54. The top corners of the wall are beautiful without any modification, but you must make it clear to the painter in advance when looking for a painter. The top corner elastic line will help to make the top corner line straight.
55. Surface treatment is very important before applying putty on the cement surface of the line trough. It is suitable to use cleaning balls to treat weak surfaces.
56. Gypsum is suitable for filling larger holes in the wall. Of course, if the hole is too large, cement will still be needed.
57. Be sure to protect the back of the frosted glass from paint, as it is difficult to clean!
58. The vegetable basin faucet must be able to be turned on and off with the back of the hand. The kind that requires fingers is not easy to keep clean, and it is also difficult to turn it when the hands are oily.
59. The price of luxury automatic clothes drying racks is too high. After comparison, we found that some unknown brands are better than first-line brands in structural design, but the price is much lower.
60. You can consider using a metal socket installed on the ground. This kind of socket is expensive, more than 100 yuan, but it is very convenient. It is usually flush with the ground, and the socket can be popped out by stepping on it. Suitable for large living rooms. Or install it under the dining room table to plug in the hot pot (to prevent wires from hanging when walking back and forth)
61. Storage room. TX has already mentioned it, but I didn’t make the cabinet doors, so they don’t look very nice, and the cabinets where clothes are placed are easy to get dirty.
62. Bed starter frame (is that what it’s called). I bought a fabric bed from a professional bed company, and spent 350 yuan to add this feature. There is a handle at the end of the bed, and when you pull it, the bed board will flip up, revealing the storage space underneath. It's great!
63. Impractical double-rod towel rack! At present, it has the same purpose as the single pole. It is basically not hung on the inner pole to dry towels.
64. I feel that the trash can in the cupboard is not practical enough, so it is better to put it outside. Also, be sure not to install door-type trash cans and countertop trash cans. Opening the cabinet doors in the summer will stink. It's better to put the trash can outside.
65. The small cabinet next to the dining table is good. It can be used to store some things, which is very convenient.
66. In my opinion, the performance requirements of the mop bucket are not high. You can build one yourself and lay it with tiles or mosaics that match the surrounding environment. It will look beautiful and save money.
67. The bathroom can have some nail hooks for hanging things.
68. The bathroom is designed with a small cupboard to store clothes, so you no longer have to worry about forgetting to take clean clothes after taking a shower. clothing.
69. A washing machine with a dryer is seriously impractical except for the only bad days of the year. Thick clothes and bath towels should not be dried in the dryer. It would be better to let the sun disinfect them. I'm overdrafted and need to save some money.
70. I made a laundry sink in the laundry room for washing some things by hand. I originally thought I would use it less, so I bought a very cheap Terry faucet. Unexpectedly, this laundry sink is so convenient and has become the most frequently used washing area in my home. Rags, socks, floor towels, all are washed in there, and even hand washing is mostly there.
71. It is really impractical to install light strips. It has not been turned on since the renovation was completed. When guests come, I just show off the spotlights. I even forgot to install this thing. It turned out that I decided to do it romantically when I wanted to have a party, but now I don’t have many opportunities to do it with spotlights.
72. The biggest lesson is that the simpler the decoration, the better. It will cause less pollution, cost less and save worry.
73. Practical stuff: ① A well-designed storage room. ②. A sink for washing dirt on the north balcony. The difference is the washbasin in the bathroom and the sink for washing vegetables and dishes in the kitchen. ③You can pull out the faucet for washing your hair in the bathroom. (Exception is TX who never washes his hair in the basin). ④ Easy-to-clean floors and suitable cleaning tools. ⑤ Kitchen countertop work lights.
74. When buying a toilet, you must measure the hole spacing of your toilet. If you don’t buy it and then return it, it would be really...
75. The bathroom and kitchen floor tiles are best after they are installed but not before they are dried. It's better to measure the level and see if the lowest point is the floor drain. If you don't wait until it's dry and then argue with the decoration team, a lot of cells will be killed.
76. The window sill is made of Zhuji stone from the Great Wall, which is an 800X800 tile. The manufacturer cuts and grinds the edges, and the masons affix them. The pattern is nice and there is no radiation.
77. The shower room in the bathroom must be large enough and made of transparent glass, so that you will not feel cramped when taking a shower inside.
78. White cement should not be used for tile joints. Within a month, it turned into black seams, which was extremely ugly.
In the end, I bought caulking agent and did it myself, which was so tiring
79. There should be a back board under the artificial stone of the cabinet, but after installation, I found that there was no one. Now I don’t dare to cut meat on it, so I promised it. It’s been almost two months since I reinstalled it and it still hasn’t been installed (I only polished it once).
80. Don’t believe the designer’s tricks. Of course, you can visit several more decoration companies and extract truly useful things from the designs of each company. The key is how you want to decorate your home.
81. If the developer has installed a smelly "bowl" in the floor drain, do not take it out.
82. After installing the tiles on the bathroom floor, test the water. If the water flows slowly, rework it immediately. The water flow in my house was relatively slow, so I felt relieved at that time. Now there is always a little water accumulation when taking a shower. Our main bathroom's shower head, which costs hundreds of dollars, is idle. Now we are always thinking about how to remedy it.
83. When installing a wash basin, consider its relative position to the mirror, the shelf for toothbrush cups, and the towel rack.
84. When buying a mirror, consider the position of the mirror headlight. If you do not want to install a mirror headlight for the time being, it is best if the size of the mirror can cover the line reserved for the mirror headlight.
85. Make a small cabinet on the balcony where the washing machine is placed to conveniently store some sundries, such as laundry detergent. Both beautiful and practical
86. Be sure to keep an eye on the upstairs for waterproofing... Otherwise, water will drip from upstairs and the wall cabinets will be in a mess... ......
87. Don’t blindly follow online group buying. I later discovered that some bargains by yourself are cheaper than group buying.
88. There must be a few more sockets on the TV background wall. Once the TVs, DVDs... are placed, you will find that there are not enough sockets.
89. Before changing the waterway, you must consider the size of the washbasin you will install in the future, such as whether it is a left basin or a right basin, and where the water inlet and drainage should be located. Otherwise, you will find that the washbasin in the photo cannot fit after the modification!
90. Regarding curtains, it is best for everyone to keep a copy of the size for themselves and explain to the boss that the size cannot be missing. If it's missing, what's the matter? Or watch him cut the cloth yourself.
91. The construction process of decoration:
1. Enter the site, demolish the wall, and build the wall.
2. Conduct a 24-hour water closure test on the bathroom and kitchen floors (the developer needs to complete this task).
3. Cut wire ducts, water and electricity renovation and acceptance.
4. The water and electricity renovation project was sealed and buried in the wire trough. There was no leakage in the closed water test and the waterproofing project was started.
5. Wall magnets in bathrooms and kitchens.
6. Carpentry comes in, hanging ceilings, and plaster corners.
7. Door covers and window covers included. Make wooden cabinet frames.
8. Simultaneous production of various wooden doors, styling doors and flat pressing.
9. Apply dust-proof paint (clear oil) to the wooden panels.
10. Leveling and laying of marble countertops on window sills.
11. The wooden veneer panels are pasted, the lines are made and carefully installed.
12. Treat, polish and level the wall base.
13. For household items, stick stickers (protective edges) on the seams around the door.
14. Apply ICI oil to the wall at least three times.
15. Furniture paint comes in, patch holes and paint.
16. Treat the corners, lay floor tiles, solid wood or composite wood flooring, waterproof marble strips, and skirting lines.
17. Installation and debugging of lamps, sanitary ware, handles and door locks.
18. Clean up, patch the floor tiles, and move out.
19. Preliminary acceptance within the decoration company.
20. The three parties will make an appointment for formal acceptance and delivery to the owner.
The first step is to go through the admission procedures: Generally speaking, the admission procedures require the original and copy of the ID card of the person in charge of the decoration team, the original and copy of the owner's ID card, A copy of the decoration company's business license, a copy of the decoration company's construction license, and a decoration deposit. Of course, you need to ask your management office specifically before applying.
The next step is to knock on the wall: after knocking on the wall, the garbage has been cleaned up, and the plasterers should enter the site. The calculation of the wall area can be based on the floor plan of the house, which contains all the detailed data about your house. Remember to measure the area of ??the wall you want to knock on before knocking on the wall. You must know that money is calculated based on the area when knocking on a wall.
The plumbers are mainly responsible for building walls, removing dust, patching up sporadic repairs, laying ceramic tiles, waterproofing, leveling the ground, and installing floor drains. Cement mortar is used for building walls and plastering, the difference is just in the proportions. Building walls and removing plaster are the preliminary tasks of the plasterer. After completing these two tasks, the plasterer will first measure the actual area for wall building and plastering, and then he will double-measure these dimensions with the owner. In addition, it is best to install ceramic tiles by one person. If it is done by two people, the effect may be different due to different styles. It is best to use caulking material to fill the tile joints. Some of the white cement parts in my house have turned yellow. Pay attention to the mud construction part: river sand should be used for decoration.
After the masonry workers put up the walls and before they dusted the walls, plumbers and electricians came in at the same time to carry out water and electricity renovations. The main tasks of hydropower renovation include hydropower positioning, trenching, pipe burying, and wiring. Although grooving is not important, it indirectly affects the quality of the buried pipe and threading. The first step in the renovation of water and electricity is water and electricity positioning, which means determining the location of the switch sockets and water connections in the whole house according to your needs. The plumber will mark the direction of the water pipes and wires on the wall according to the location of the switch sockets and water faucets. Lines are the layout of lines. Remember to ask your renovation team for a water and electricity diagram, and ask the plumber to explain the line direction to you clearly according to the diagram. Don’t be afraid of trouble. The plumber will definitely meet your requirements. After the water and electricity renovation is completed, if you don’t Sign, plumbers don't want to get money from the decoration team leader.
After the water and electricity are positioned, the next step is to make grooves. The grooves made by a good groover are basically a straight line, and there are basically no teeth on the edges of the grooves. Note that before drilling grooves, be sure to ask the plumber to mark all the water and electricity directions on the wall. Remember to compare the water and electricity diagrams to see if they are consistent.
There are a few other points to note regarding hydropower renovation: 1. It is best to indicate in the contract the brand of wires used for circuit renovation. 2. The switches throughout the house should be basically at the same level. 3. The sockets in the whole house should be at the same level as possible, except for special sockets such as air conditioners, refrigerators and special requirements. 4. The colors of the phase wires and neutral wires during circuit modification should be consistent in each house. If possible, it is best to indicate the colors of the live wires, neutral wires, and control wires in the contract, and the protection wires according to The national regulations are yellow and green. 5. It is best to use 3 wires with 4.0 strands for socket wires (including air conditioners and refrigerators), and 2 wires with 2.5 strands for lighting wires. 6. The bottom box is buried. If possible, it is best to buy the bottom box yourself. Please ask the decoration team to report the installation fee. 7. Regarding audio cables, if you are not a professional audiophile, it is best not to install audio cables: The area of ????the houses in Shenzhen is basically about 100 square meters, and the living room area is generally not very large. Install audio in such an area. The effect is really not necessary for ordinary people. Air traffic controllers also have to count money.
Regarding the waterway renovation, I think it is necessary to say one thing: regarding the issue of cold hot water, based on the weather in Shenzhen
Does it need to be connected to the washbasin and kitchen? Do all the vegetable sinks use cold hot water? If you need hot water, just turn on the water heater and connect it.
Just like many mobile phones nowadays have Internet access functions, but how many of us use mobile phones to access the Internet? But we do have to spend a lot more money for a mobile phone with Internet access. When I got the settlement form, I could only lament that it is so easy to make money but spend money!
Finally, it is best to note it in the contract. Ming must wait until the water and electricity renovation is completed before the carpenter enters the site. The advantage of this is: you don’t have to pay attention to two things at the same time. Water and electricity renovation is a very important expenditure in the decoration, and it is also the bulk of the decoration company’s profits. Moreover, the water and electricity renovation is very concealed. If carpenters come in at the same time, it will distract you from your full attention on the plumbing renovation. When renovating waterways, pay attention to keeping them neat and tidy. When signing a contract for waterway reconstruction, it is best to indicate the materials used for waterway reconstruction. In addition, when renovating waterways, attention should be paid to the size of the original sewer pipes in the room. The pipes connected to the original sewer pipes in the house should preferably match the original sewer pipes.
When renovating a circuit, you should think about where all the lamps in the house will be installed in order to determine the location of switches and sockets. At the same time, you should also note that the prices of new buried wires and replacement wires are different. When buying a doorbell, it is best to buy a wireless doorbell. The main tasks of hydropower renovation include trenching, burying pipes, and threading. Although grooving is not important, it indirectly affects the quality of the buried pipe and threading. After the water and electricity renovation is completed, carpenters will enter the site. When doing carpentry, please pay attention to the following: 1. When you get the designer's drawings, it is best to carefully review the dimensions before signing. 2. The ownership of carpentry toolboxes, workbenches, air compressors and other tools belongs to the decoration team leader or the decoration company. 3. Before the carpenter enters the site, the boards should be brought in first. Check carefully whether the boards entering the site are in compliance with the contract and whether they are genuine. Remember to hire a termite company to prevent termites.
Like plumbers and electricians, carpenters are also the main source of profit for the decoration team. The main source of formaldehyde in decoration. To control this, in addition to the board must comply with national environmental protection regulations, the wood varnish used must also be selected well. I will mention this later. The painter must enter the site to apply putty after the plasterer has finished painting the plaster wall and it has dried. This is the first stage of painting mentioned in the schedule. If there is a gypsum line installed, it will also be installed at this time. The gypsum line will be installed at this time. The line is a matter for painters. Remember not to use 107 when applying putty. According to my upstairs neighbor, 107 will slowly release a gas that is harmful to the human body, so it has now been replaced by 108.
If the decoration is painted on one base and two sides, it must be sanded three times. The first sanding is after applying the putty and before starting to apply the first coat of primer. Polish the dry wall once. The first coat of wall can be polished with sandpaper with a lower grade, such as 360#; the second polish is after the primer is applied and it is completely dry before the first coat of topcoat is applied. At this time, use It is best to use sandpaper that is higher than the sandpaper used in the first pass, such as sandpaper above 400#; the third pass is after the first coat of topcoat is applied and it is completely dry before the second coat of topcoat is applied. At this time, be sure to use high-grade sandpaper. Use graded sandpaper to polish the wall. It is best to use 600# or above sandpaper to polish the wall. Only in this way can the wall painting effect be guaranteed. Otherwise, after your wall is painted, it will most likely feel like flour to the touch.
Another issue to mention is the problem of adding water to the paint. Each type of paint has certain restrictions on the proportion of water added. You should pay attention to strictly follow the construction instructions.
92. Before reinstalling the flue valve, it must be wiped clean to ensure that the valve can open and close freely and can be opened to the maximum, otherwise it will affect the smoke exhaust effect of the range hood. You can leave two strips uninstalled when installing the suspended ceiling, and then install the suspended ceiling after the range hood is installed and tested correctly.
93. In a space as large as the living room and dining room, if you can’t afford a suspended ceiling, don’t do it.
94. When routing the cables, think about the position of the air conditioner and move the power supply as close to the air conditioner as possible to avoid seeing a section of the power cord when installing the air conditioner, leaving a trace of regret.
95. Personally measure and record the various dimensions available in the house. You can cover up the dimensions on the floor plans and re-mark them. The final dimensions will directly affect the decoration design and furniture purchase.
96. If you choose black walnut for a small apartment with poor lines, it will not be grand enough. At this time, you need to make a choice, either to accommodate the reality or to stick to your own ideas. Of course, it is best to consider both
97. Start looking for decorators. From personal experience, if the apartment is not particularly large and you plan to simply decorate it, it seems more cost-effective to find a guerrilla. It is best to introduce it after others have installed it, and you can see it with your own eyes and agree with it. It is especially important to feel about the person in charge of the decoration. What is your sense of responsibility and appreciation level?