The size of the factory gate depends on the light star of Lubanchimen.
The feng shui size of the factory gate is roughly suitable. In the factory, there are several gates in and out, there is no primary and secondary, or the walls are irregular and have gaps, which is also a sign of chaos. Moreover, for example, if the passage in a company or factory is unclear, turning left and right will easily lead to unclear geomantic omen, which is a big taboo.
There is an east-west road in front of the door, which is convenient to travel (with traffic advantages). Boss Cheng (the factory owner) opened the door in the north of the factory for the convenience of transportation, and built a path by himself, which can go straight to the factory, so it is convenient to get on the bus. Of course, this original intention must be for the benefit of the factory, but this unintentional move has made a feng shui taboo: "The gate collided with the main office building."
The factory gate faces uphill, and the gate is stepped to relieve the downward water potential. After the water potential is weakened, there will be no disaster. But remember, even number of steps is not appropriate, and odd number is auspicious, such as level 3 and level 5; Or put a statue of Guan Gong at the entrance of the gate to ease the downward flow of people.
Factory doors include fire doors, Class A fire doors, Class B fire doors, wooden fire doors, steel fire doors, glass fire doors, security doors, workshop sliding doors, garage doors, rolling doors and so on. As a factory, the door should be matched with the factory building, and the size is too small. In order to facilitate the transportation of goods and equipment, the size of the factory gate should allow container trucks to pass through.
The factory gate should not be too high. When the door is too high, you will get used to looking up when you go in and out. There are vain and flattering psychological hints, and dealing with things is too arrogant. The lintel is too high, even higher than the ceiling, which will cause fewer and fewer people in the family.
The factory gate should not be too low. The door is so low that you have to bend over to get in and out. Over time, people's eyes are used to looking down, and when they encounter strong things, they will choose to bow their heads and yield, thus becoming short-sighted, timid and inferior, relying on others all their lives and being bullied.
The factory gate should not be too wide. The door is too wide to hide the wind and gather the gas. Not only can not keep money, people will be scattered, and the body will become weaker and weaker. The door is too wide, and the old people at home will feel hard.
The factory gate should not be too narrow. The door is too narrow, the progress is uncomfortable, there is a sense of oppression, the line of sight narrows, and the mind tends to narrow.
How big is the bronze riser hanging in front of the factory? Generally, 32 * 2.2m, 35 * 2.3m and 30 * 2m should not exceed the length of the board, and the width is generally between 30 and 35cm.
The size of the door of the factory workshop should be at least six meters high, and the width should be subject to the size of the door.
How wide is the warehouse door? The door has no standard size. They are all made of measuring ruler, which is related to the height of the shutter door. The higher the height, the thicker the diameter is needed.
Calculate size:
1. The hole height refers to the height of the doorway;
2. The part above the doorway;
3. The actual width of the shutter door should include the width of the guide rails on both sides;
4. Fire prevention and plugging requirements are not considered in the quota.
The size of the warehouse shutter door is mainly determined by the height and width of the house, because it can actually be made without any restrictions. The height can reach about 9 meters to 14 meters, and the width can also range from 4 meters to 12 meters. Generally speaking, the common garage shutter door size will choose 80 mm round tube when choosing the shaft diameter, and then determine the use according to the size of the door. Generally, the size of a small single garage door is about 2.5 meters high and 3 meters wide. When choosing, generally choose 55 or 77 curtains. It is made according to the size of the website. As big as it is, there is no specification.
In addition to rolling doors, warehouse doors are more sliding doors, which can be one-way or two-way according to the space of storage bodies at the entrance of the building; Single or multiple overlapping fans; Generally, according to the load-bearing structure of the door body, it is divided into 50OC/Information/News Details /3 170 to judge whether it is a straight line or a combination of straight lines and curves.
How to design the factory gate? How high is it? The width and height of the factory gate are based on 300, such as 3.6m*3.6m, depending on your requirements. The width can be within1800 mm. When the wooden door is large, the aluminum alloy door needs to be widened by 600- 1000, and the height of the truck is increased by 400-500 when it is fully loaded.
According to the fire protection law, how big is the factory and how many doors are there? The number and area of factory gates are irrelevant. No matter how big the factory is, it requires no less than two gates, that is, more than two gates can be designed.
The Fire Protection Regulations have strict requirements on the layout of roads and workshops in the factory. That's the point. The idea of fire fighting is your own factory, and no one will make the gate small. Vehicles on the scene can get in and out of the fire truck.
I hope it helps you. You can ask if you don't know. Thank you.
What is the size of the company name on the factory gate? There are no specific regulations.
According to the size of the gatehouse and the distance in front of the door, decide how big the font needs!