1 Definition of blank: between stickers or between stickers and words. If you need to glue to make a three-dimensional structure, it is called blank space. Blanking can be done without printing oil, which is convenient for gluing.
2. the practice of white position: when doing white position,
A) Be sure to have an OK sample book (such as a white sample book, a color draft sample book or a blue sample book), draw the outline of the paste position with a red stroke, and then remove the stickers from the sample book one by one.
B) Put it under the beer film, register the color position and position it with double-sided adhesive tape.
c)。 Indent about 3.5mm on each side of the outer frame of the sticker, draw a frame, draw a diagonal line in the frame and mark the words "white position". The white position in the text is the same as that on the sticker!
D) After all blank spaces are completed, a set of blue paper must be submitted to the printing room for drying, and a blue paper sample should be made to confirm whether the blank spaces are wrong or not, and the incorrect blank spaces should be corrected until there is no problem.
Second, draw the print line or nail hole position:
1. Purpose of printing lines and nail holes: When a pop-up book sticks a sticker on the book block, it is easy to locate and improve work efficiency.
2. The practice of printing lines:
A) The two ends of the pasting position on the text (that is, the inner sides of both ends next to the pressing position and the glue placing position) are respectively indented by 1mm, and one side of the pressing position is indented by about 1mm, and a line (or point) with a length of 2mm can be drawn at both ends.
b)。 Print lines (dots) need to be printed.
3. The practice of pinhole:
A) Stick a nail hole at two sharp corners of the card position on the text.
B) This nail hole doesn't need to be printed. It will be marked with "+"on the beer line and then made on the beer mold.
3. Common sense of text structure of 3.pop-up book: that is, common sense of organ folding structure.
1.pop-up most of the words in the book are organ folds. Organ folding structure mainly has the following characteristics.
A) After the book block is closed, the book mouth and spine should be flush.
B) organ folding books are mostly composed of several organ folds, and there is a corner at the end of each page (except the last page).
c)。 The organ folds the book without exposing the edge, and the size of the brewed book block is the size of the finished product.
2. Organ folding books should pay attention to when drawing beer lines:
A) All pressing lines (that is, all organ folding lines) should be perpendicular to the two knife lines on both sides of the foot and head of the book.
B) When typesetting between two pages, double cutter positions should be reserved, and 6mm bleeding position should be reserved between cutter positions.
C) For the two pages to be spliced, a poster is usually made at the end of the previous page as the splicing position, which is spliced with the first page of the next book block;
D) The width of Li is about 13mm, and both ends should be chamfered.
E) When drawing a beer line, the fold line of the front book block should be shrunk by 0.5mm, and the tangent line of the back book block (that is, the fold line between the head page of the book block and the front book block) should also be shrunk by 0.5 mm. Except for these two places, the distance between other fold lines and fold lines should be the same, so that the book block will be flush after being closed.
Note: Some organ folding books have no convenient position, so it is not necessary to reduce the size of the two-page folding position, just the opening of the folding book is flush with the spine.
Four. Common sense of sticker structure
1. After the book is closed, all stickers must not exceed the book block.
2. The pattern on the label should be complete and centered. If there is no other influence, the pattern is generally 1.5mm away from the edge.
3. Generally, the width of the adhesive layer of the sticker is about 12mm, and the length depends on the shape.
4. If the knife and the pressure are in a straight line, when drawing the beer line, the position of the knife is usually indented by 0.5 mm. 。
5. Usually use a 2mm long oblique knife to cut at 45 degrees on both sides of the needle mouth of the sticker.